https://bastyon.com/index?v=f5ca02c2802c9653e0a788f489c8b1f3714d1c010ef2d058b1fc7e3c6f5c077d&video=1

ANNOUNCEMENT: This content is now being posted EXCLUSIVELY ON BASTYON and no longer added to on Telegram. I don't have time to waste publishing stuff where it can be completely blocked any day.

I can't possibly over-encourage you to download the app from https://bastyon.com/applications and use that instead, so your access to Bastyon content can't be blocked.

https://bastyon.com/AircreteDomestead

Several posts at the link have brought the documentation up to date.


I can't possibly over-encourage you to download the app from https://bastyon.com/applications and use that instead, so your access to Bastyon content can't be blocked.

Here's the latest

https://bastyon.com/index?v=e40513b8243ae8c44b81a3e3c98503543e706f790f75851400a447d0b6ddb0b8&video=1

Looking for suggestions from people with real experience with saw mill saws.

After deciding on the best way to saw blocks efficiently, the entire state of the art building process may be ready to go commercial. For short blocks in the bottom portion of the dome, three sides are cut, plus maybe a 4th when the pour top isn't parallel enough with the bottom. After about 45 degrees up the dome, above the equator, four cuts are required to keep the block laying efficient with minimal mortar which is much less insulating. 39" long arch blocks only need the top and bottom cut, with one needing to be cur at an angle to the other in the top portion of the arch. A friend very familiar with saw milling has seen what cuts are needed and will be making some suggestions. Other opinions from saw mill experts would be nice.

The bottom, as poured, of each block (11" tall, 8" thick, 39" long, 40 lbs) has a powdery surface, sometime with recesses where excess liquid pooled on the form. So, the bottom of the block needs to have 1/2 to 1" sliced off.

For arches, the top of each 39 inch long block will be skimmed mostly parallel to the bottom, if more than 1/2" out to start. Blocks in the top portion of an arch need this second cut to be at an angle so that the outside is wider than the inside for narrow mortar joints.

As needed (over 1/2" out of parallel to bottom), the 39" long blocks to be cut to 13" for the lower portion of the dome, would need to have the top skimmed off mostly parallel to the bottom, like the bottom blocks in the arches.

For blocks in the cylindrical section, 3 courses below the dome equator, after cutting the bottom and top, each block will be tipped over on a side and cut square to 13 inch lengths.

For the dome above the equator, the length cuts alternate +/- 3 degrees for a 20 ft dome (2 degrees for 30 ft) downward thru the 8" thickness. The long side is 13 inches to get 3 blocks out of each large block. This angle cut laid on the block below causes the dome blocks to naturally tip inward and have a minimal mortal line all the way through. Note, maybe two saws arranged to cut both ends of a block in the same setup may be best, to avoid rolling the block over or changing the saw angle before every cut.

The dome blocks are tipped and laid so the as-poured top is on the side against the as-poured bottom of the next block in the course. As the courses get higher and tip inward more, this fit between the blocks, cut parallel top to bottom (side to side as laid), causes a triangle shaped gap to open up. The lower side of this gap gets wider with height. Eventually, the as-poured top of the 13" blocks with the +/- degree cut ends need to have a compound angle cut to minimize the triangle gap for minimal mortar. The cut changes with every higher course and is done based on actual measurements. It's likely that the 39" long blocks used to make these short blocks may not have the top skimmed, to avoid an unnecessary top cut. This last cut may remain hand sawn at the construction site, if the ROI of this least used and most complicated band saw isn't justified.

BTW aircrete is brittle. So a band saw should damage them less than a fast reciprocating saw.

Of course, there's the bottom line. The band saws with large tooth blades need to be a reasonable cost. If you have any suggestions for saw types to use, it would be much appreciated.

FYI current mixing/molding method for blocks ready to cut requires 11 manhours to produce either 22 long blocks (one complete arch) or 66 short blocks (66 linear feet of dome block courses).

Today we blew away the old record of about 50 for the number of blocks laid in a day. 82 blocks in a single day. Yay!!!

Discussed the @AircreteDomestead project. That's taking a large majority of my time, until we have to stop for winter.

Also, visited about other stuff around our homestead, natural health, Qortal, Bastyon, Midfest, etc. Hope y'all enjoy the interview which is audio only.

https://www.freedomsphoenix.com/Media/350221-2023-09-11-2023-09-11-ernest-hancock-interviews-mike-swatek.htm

Just posted a status update at Bastyon.com/AircreteDomestead

There are three new posts today at Bastyon.com/AircreteDomestead

Ernest Hancock interviewed both Brian and I at Midfest, near the AircreteDomestead project. We covered quite a bit about it starting at 4:23:33.

https://www.freedomsphoenix.com/Media/352555-2023-10-21-2023-10-21-ernest-hancock-interviews-attendees-guests-midfest-spavinaw.htm

Finally had a chance to investigate the difficulty accessing videos on Bastyon. The earlier videos were all published on an old Windows machine which has been off mostly since finishing my Linux migration. Seems the data hadn't propagated into the network enough from people visiting and following. So, I've left that old machine on for a day. Followed on a couple of other PCs and left them on to fully import and host all the data. If others would do the same, the data will persist and load faster.