🔖Don't forget to read the Reduction of responsibility :

For @ByBedircanKernelCases and @ByBedircanKernelCases_support

Please read the Reduction of Responsibility for @ByBedircanKernelCases and @ByBedircanKernelCases_support

1:) These are definitely not builds; they were rearranged by me using an advanced unpack-repack method.
2:) They are based on different kernels.
3:) Don’t be toxic, these are not official builds.
4:) You are responsible for any bootloops, hard bricks, or other issues (lol).
5:) Always be tolerant and common sense
6:) If you are a kernel maintainer and I make changes to your kernel, please contact me in the group if you prefer that I do not do so, your understanding is appreciated.
7:) All files are beta, read before posting any feedback join support group and #ByTesting_cases
8:) I am not kang (copying) in any way, and neither should you! ( I basically state that I use a different base, this is not kang)
9:) Join the group for flash steps, then check join support group #bycases_flash
10:) It is your responsibility to read the group rules

Device: Xiaomi 11T Pro | Vili
Based on kernel files: HyperOS 1 Android 14 Elite Lite ROM
Supported versions: Android 14+++ and HyperOS
Contributor: @BdrcnAYYDIN

Changelog:
⦁ SELinux set to permissive mode
⦁ Optimized voltage transmission between the touch sensor and processor
⦁ Reduced unnecessary battery usage for 4G and 5G
⦁ Improved idle power consumption
⦁ Reduced excess power consumption of the touch sensor
⦁ NFC automatically turns off when the screen is off and not in use
⦁ Guaranteed 0% performance loss

Kernel stuff community:
Official Repository: @ByBedircanKernelCases
Official Support: @ByBedircanKernelCases_support

🔖Don't forget to read the Reduction of responsibility :
https://news.1rj.ru/str/ByBedircanKernelCases/7

Potential gains:
⦁ 3% reduction in idle power consumption over 24 hours
⦁ 1.5 hours longer daily usage
⦁ 2.5% lower screen power consumption
⦁ Most importantly, 0% performance loss guaranteed

⚠Read before use:
• Be sure to read it in the support group before flashing
• Be sure to read it in the support group before testing
• Be sure to read it in the support group before feedback

§ Kernel helper Additional modules:
Soon

Device: Poco F7 | Onyx
Based on kernel files: HyperOS 2 Android 15 Zendroid ROM
Supported versions: Android 15+ and HyperOS 2
Contributor: @BdrcnAYYDIN

Changelog:
⦁ SELinux set to permissive mode
⦁ Improved parameters for more efficient battery usage when the device is idle
⦁ Less performance degradation in case of overheating
• Removing unnecessary restrictions for short-term temperature fluctuations
• Switched to thermal governor instead of thermal throttling at the kernel level, and support has been added
⦁ Guaranteed 0% performance loss

Kernel stuff community:
Official Repository: @ByBedircanKernelCases
Official Support: @ByBedircanKernelCases_support

🔖Don't forget to read the Reduction of responsibility :
https://news.1rj.ru/str/ByBedircanKernelCases/7

Potential Gains:
⦁ 8% to 18% increase in overall device battery life
⦁ Average operating temperature drops by 1°C to 4°C under heavy load
• Under heavy load, the thermal throttling activation process is delayed by 15% to 25%
⦁ Most importantly, 0% performance loss guaranteed

⚠ Read before use:
⦁ Be sure to read the support group guidelines before flashing
⦁ Be sure to read the support group guidelines before testing
⦁ Be sure to read the support group guidelines before giving feedback

§ Additional Kernel Helper Modules:
Coming soon

Device: Device: Realme X7 Max | RMX3031
Rom : ColorOS 16 - Android 16
Based on kernel files : ORIGIN 4.19.325
Contributor: @BdrcnAYYDIN

Changelog:
⦁ SELinux set to permissive mode
⦁ Haptic Feedback (Vibration) Improvement
⦁ To maintain stability, I increased the charging current limits; This will allow the device to charge faster.
• Better screen refresh rate experience
• Stronger signal reception
• Fingerprint sensor faster reading and detection
• Stronger and more noticeable vibration
⦁ Guaranteed 0% performance loss

Kernel stuff community:
Official Repository: @ByBedircanKernelCases
Official Support: @ByBedircanKernelCases_support

🔖Don't forget to read the Reduction of responsibility :
https://news.1rj.ru/str/ByBedircanKernelCases/7

⚠ Read before use:
⦁ Be sure to read the support group guidelines before flashing
⦁ Be sure to read the support group guidelines before testing
⦁ Be sure to read the support group guidelines before giving feedback

Our support group for stickers and gifs packs is published!
Feel free to chat while using gifs and Stickers, represented by the best emojis, with great quality and improvements. @tgasfstickers_cht
You can join our group and access packs or request more quality content.