Forwarded from Gateway Pundit
Video: Kelsey Grammer Shares Jesus With Old ‘Cheers’ Bar Buddies in Incredible Interview
https://www.thegatewaypundit.com/2025/02/video-kelsey-grammer-shares-jesus-old-cheers-bar/
https://www.thegatewaypundit.com/2025/02/video-kelsey-grammer-shares-jesus-old-cheers-bar/
The Gateway Pundit
Video: Kelsey Grammer Shares Jesus With Old 'Cheers' Bar Buddies in Incredible Interview | The Gateway Pundit | by Ole Braatelien…
Grammer opened up to actors Ted Danson and Woody Harrelson during a podcast in which Danson and Harrelson interview celebrity guests.
Forwarded from David Avocado Wolfe
Lyme’s disease was created by Dr Erich Traub in Plum Island, New York laboratories, an Operation Paperclip Nazi. His specialty was “gain of function” on tick-borne diseases.
This disease has destroyed the lives of millions of people and was completely denied by the big pharma Rockefeller medicine system.
Join: @davidavocadowolfe🥑
This disease has destroyed the lives of millions of people and was completely denied by the big pharma Rockefeller medicine system.
Join: @davidavocadowolfe
Please open Telegram to view this post
VIEW IN TELEGRAM
Forwarded from The Deer Blind
Please open Telegram to view this post
VIEW IN TELEGRAM
Forwarded from Working Men Memes (Wesla Johnkowski)
Drilling and Tapping threaded holes.
Because the thread angle is 60degrees... and the COS of 60 is 0.5, each side of a bolt's thread is 1/2 of the pitch distance. It means you just subtract the thread pitch from the bolt diameter to get the pilot size. It means that a M5 x 0.8 bolt has a pilot hole size of 5 - 0.8 or 4.2.
Thanks to 60 degree threads, you take the major diameter and subtract the threads per mm or threads per inch to get the pilot hole diameter.
Metric is easy... M6 x 1.0 is 6 minus 1 = 5mm pilot hole.
SAE... 1/4-20 thread. Convert 1/4 to decimal. Convert 1/20th to decimal. Subtract 0.25 - 0.05 = 0.20 . Go to drill index and find there is no 0.20 drill but a Number 7 drill is 0.201. Easy! right?????
Because the thread angle is 60degrees... and the COS of 60 is 0.5, each side of a bolt's thread is 1/2 of the pitch distance. It means you just subtract the thread pitch from the bolt diameter to get the pilot size. It means that a M5 x 0.8 bolt has a pilot hole size of 5 - 0.8 or 4.2.
Thanks to 60 degree threads, you take the major diameter and subtract the threads per mm or threads per inch to get the pilot hole diameter.
Metric is easy... M6 x 1.0 is 6 minus 1 = 5mm pilot hole.
SAE... 1/4-20 thread. Convert 1/4 to decimal. Convert 1/20th to decimal. Subtract 0.25 - 0.05 = 0.20 . Go to drill index and find there is no 0.20 drill but a Number 7 drill is 0.201. Easy! right?????
Forwarded from Foxx Den 🦊
2 F's back ups active https://x.com/aColdStew https://x.com/10acity__
Forwarded from Meme Cannons (ZΞЯФ)
This media is not supported in your browser
VIEW IN TELEGRAM
Forwarded from Patrick SighOp Archive.
This media is not supported in your browser
VIEW IN TELEGRAM
Manic Monday is once again upon us, make the best of it.