https://www.youtube.com/watch?v=zsX0zHB4LwE Whelp tunes. my current attitude toward blender. If you don't stop wrecking my model, YOU'LL GET KNOCKED THE FUCK OUT

You know what? Blender can eat it. I'm not going through the headache of splitting this whole model in half today. I'll print it solid. No inside supports. No greenstuff. None of that.

If you can't split the model in half... just put a cone through it. Boom. Save on resin/filament, and the supports will just slide right out. No green stuff. No bullshit. Just good old sanding.

No holes, no greenstuff, no fancy jazz. Just gotta get my pumpkin ornament out of the printer, get this thing on the USB thingy, and we're good.

Threw 'er in the prin'er. Time to go play video games. Need to go into palworld and build a base dedicated to extracting crude oil. DADDY NEEDS HIS JUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUIIIICE

The spookyposter bust Mk 2 has been taken out of the wash. and it's HUUUUGE. It dwarfs the Mk I. And the best part? All the supports just came right off. Not a single support anywhere in sight. Of course I hollowed out the middle a bit. There's a cone underneath, but that's it. My pumpkin ornament doesn't fit perfectly around the little ball in the middle meant to hold the hat BUT that's ok too. It'll be the one (and last) time I use green stuff (hopefully.)

Hey Vern, it's the third reich! (wanted to save this before I carried on

GA and habby birthday to me! The spookyposter bust still hasn't fully dried off yet. So I'm leaving the doors to the shed open. That should do the trick, right? Once that's done, I'll throw it right into the curing station. Speaking of the curing station, I've thrown the pumpkin ornament in there too. All three pieces. It should be ready by now, so I'll go out there and take it out. Prime it in the box alongside the MK 1 Spooky bust (Giving it away to someone out here that wants it despite it being a mess. Not wasting resin.)

I've cured the middle part of the ornament. The inside still looks wet. I think maybe I need to put it by the door so it can air out.

also it needs to be sanded a little bit

The spooky bust is dry, so I've thrown it in the curing station.

Reminder to craftsfrens: KEEP YOUR GLUE/RUBBER CEMENT CLOSED TIGHTLY! I just accidentally spilled like half my bottle of Mr Rubber Cement! It was a nightmare to clean up.

Took some video of the bust in the curing station, but Openshot is being a Bitch Ass Nigga and crashing when I try to edit it.

Went out back and sprayed the new spookybust with some primer. And primed parts of the pumpkin ornament too for good measure. I should probably finish printing what I have on file soon. It is getting cold and, as you probably saw from my video, the temperature might be causing some warping. It looks like 3D printer season is going out with a whimper. To be honest this printer season sucked. I've had to purchase two new vats this year, wasted money on resin that refuses to co-operate with my settings, and have very little to show for it. I intend to finish my prints and pack everything up for next year.

I got little kitty big city today. So this is where I've been when not griping about printer season.

I have two full hours of my gameplay recorded. I'm chopping out some choice clips to share.

Ever since I quit my job, became a cat, and just started batting potted plants from a 10 story building, I've become a much happier person.

This cat is culturally appropriating dragons >:( #KittyKancelation

Do your worst, human. I have already won.